Blog
Blog

Gas Dryers at CNG Stations: Dew Point and Column Selection

Gas Dryers at CNG Stations: Dew Point and Column Selection
SHARE NEWS
Added Date : 20 11 2026

In a CNG station project the three subjects that get discussed most are the compressor, the storage and the dispenser. The dryer usually sits at the bottom of the list. Yet the water carried in the gas is the component that damages the most expensive parts of the station and stops filling in winter. This guide explains why dew point is judged at the compressor outlet, and what separates the three levels of natural gas dryer.

Pipeline gas can look dry

The moisture content of natural gas is described by its water dew point: the temperature at which the gas begins to release water at a given pressure. The design rule for a station is clear. The water dew point of the natural gas at the outlet of the filling station should be sufficiently below the lowest ambient temperature at which the station operates.

There is one detail that is easy to miss here, and it is the effect of compression. On a given pipeline the dew point of the gas can be extremely low when it reaches the compressor, while that value will be significantly higher as the gas leaves the compressor. Looking at a pipeline analysis and assuming the gas is already dry is therefore misleading. The criterion is not the compressor inlet but the station outlet.

What water does to a station

Water that condenses at high pressure creates two separate problems, and both affect parts far more expensive than the dryer.

The first is corrosion. Condensed water, together with the other components present in the gas, creates an aggressive environment on the inner surface of the pipework, the storage cylinders and the vehicle cylinders. This is damage that is invisible from the outside and progresses over years.

The second is freezing. High pressure gas expands at the dispenser and as it passes into the vehicle cylinder, and it cools as it expands. Water carried in the gas drops out at that point as ice or hydrate, causing blockages on valves, regulators and the nozzle. This is why dryer capacity is selected for the lowest temperature at which the station operates in winter, not for its summer conditions.

Three levels of dryer

Natural gas dryers are offered at three levels according to the flow rate of the station and its tolerance for downtime. All three are available in the dryer product group.

1-Column

This is the low cost, low capacity basic package. It requires external regeneration or replacement of the desiccant material. It suits low to medium flows and a low to high pressure design, and is recommended for stations with low volume filling requirements.

Regenerable 1-Column

This is a rugged, skid mounted series of column regenerating natural gas dryers. The regeneration cycles are closed loop, operator activated and heat reactivated, and the system signals when regeneration is required. It suits medium to high flows and a low to high pressure design, is recommended for average volume filling requirements, and keeps downtime to a minimum.

Regenerable 2-Column

This version is designed and built for medium to large flows and uninterrupted service cycles. Desiccant regeneration is fully automatic, which maximises dew point performance and energy efficiency. Because an additional drying column takes over whenever regeneration is required, the system has no downtime.

Which column for which station

Three questions settle the decision:

  • What is the daily filling volume? A single column basic package can be enough at a low volume station; as volume grows the regenerable series becomes the sensible choice.
  • How much downtime can the station tolerate? At a fleet filling point or a station that stays open all day, a stop during regeneration is lost sales. Where no downtime is acceptable, the two column version is selected.
  • What is the lowest ambient temperature at the site? The dew point target is set from that temperature; the same station design does not work with the same dryer in a mild coastal climate and in a region with hard winters.

Dryer, compressor and storage are selected together

The dryer is not a standalone accessory. It is part of the same chain as the compressor and the gas storage. The most common mistake in the field is to increase station capacity and leave the dryer as it is. Once the compressor is replaced and the flow increases, the existing dryer starts working outside its design range; the dew point rises and the problem appears not as a dryer fault but as complaints coming from the dispenser side.

The same logic applies in the other direction. A dryer selected far larger than required means unnecessary investment and unnecessary energy consumption during regeneration. The sound approach is to size the dryer against the current flow of the station together with the capacity planned for the near term.

The dryer routine in operation

A dryer is not equipment that looks after itself once installed. A short routine is enough:

  • Follow the regeneration signal and do not postpone the cycle.
  • Record the life of the desiccant material; on single column packages replacement should be planned rather than reactive.
  • Keep measured dew point values with their dates. A rising trend is the clearest indicator available before a failure appears.
  • Before winter, review the dew point target against the lowest temperature of the region.
  • Add drain and filter points to the periodic maintenance list.

2A Engineering supplies CNG compressors, dryers, gas storage systems, dispensers and the remaining station equipment as a single chain, and supports station projects with its service network.

Frequently asked questions

Is a dryer mandatory at a CNG station?

The water dew point of the gas at the station outlet should be sufficiently below the lowest ambient temperature at which the station operates. If pipeline gas does not satisfy that condition at the compressor outlet, a dryer is required.

If the pipeline gas is dry, is a dryer still needed?

Compression raises the dew point. A value that is extremely low at the compressor inlet becomes significantly higher at the outlet, so the assessment is made on the outlet rather than the inlet.

What is the difference between a single column and a two column dryer?

The two column version has an additional drying column that takes over when regeneration is required, so no downtime occurs. With single column solutions there is a stop during regeneration or desiccant replacement.

What damage does water in the gas cause?

Water that condenses at high pressure causes corrosion in the pipework, the storage cylinders and the vehicle cylinders, and it forms ice or hydrate at the expansion point in the dispenser, leading to blockages.

What data is needed to select a dryer?

Flow rate, working pressure, daily filling volume, the station's tolerance for downtime and the lowest ambient temperature of the region. A selection made without these five figures ends up either undersized or oversized.

Blog Archieve
Whatsapp
Trade Now!