Blog
Blog

Automatic Temperature Compensation (ATC) in LPG Dispensers

Automatic Temperature Compensation (ATC) in LPG Dispensers
SHARE NEWS
Added Date : 20 11 2026

An LPG dispenser does not sell mass, it sells volume. One litre of liquid LPG at 5 °C and one litre at 35 °C contain a different amount of product, because LPG expands as it warms. On a hot afternoon the same litre on the display carries less energy than it did in the morning. Automatic Temperature Compensation, usually written as ATC, is the system that closes this gap. For a station operator it is both a legal requirement and a commercial detail that quietly affects margins every day.

Why temperature matters in LPG measurement

LPG is stored and delivered in liquid form under pressure. Liquids expand with temperature, and LPG expands considerably more than water or diesel. Between the storage tank buried in the ground and the hose lying in the sun, the product can easily change several degrees on its way to the vehicle. The meter inside the dispenser counts the volume that passes through it at that moment, not the volume the customer would have received at a reference temperature.

Without compensation this creates two opposite risks. In hot weather the customer pays for expanded product and receives less energy than the display suggests. In cold weather the station delivers denser product and loses margin on every fill. Neither situation is acceptable in a market where fuel is sold by the litre and verified by law.

What the ATC system does

The ATC device measures the temperature of the product at the point of delivery and corrects the measured volume to a reference temperature. The dispenser then displays the corrected quantity rather than the raw reading of the meter. In the LPG dispensers supplied by 2A Engineering, the ATC probe uses a microchip sensor able to detect a change of 0.0001 °C, and the correction is applied according to the density setting stored in the electronic unit.

Three points are worth understanding about how the system is built:

  • The ATC unit must be coupled to the electronic system of the dispenser, not operated as a separate indicator. The correction has to reach the counter that produces the sale.
  • Any density change must be made through a password entry, so that the correction factor cannot be altered during routine work at the forecourt.
  • Both the ATC probe and the connection between the probe and the electronic unit must be sealed. A broken seal invalidates the measuring system until it is verified again.

A properly configured dispenser also refuses to sell while the ATC is in the closed position. If the system is switched off, the dispenser should stop rather than quietly deliver uncorrected volume.

ATC and the accuracy of the meter are two different things

Operators sometimes assume that a dispenser with ATC is automatically accurate. The two subjects are related but separate. ATC corrects for temperature. The mechanical meter inside the dispenser, known as the prima meter, determines how precisely the volume is counted in the first place. A four piston prima meter working with an improved magnetic system has a measurement accuracy of around 0.5 per cent, and it holds OIML R117 certification for that purpose.

Over time, mechanical wear, product contamination or a damaged pulser shaft will push the meter away from its original accuracy. ATC cannot compensate for that drift, because it has no knowledge of it. This is why the accuracy of the meter itself has to be verified at regular intervals with a reference device, the LPG master meter. The recommended practice is to check dispenser accuracy twice a year within the standard service period, and to have the master meter itself calibrated once a year by an accredited organisation.

What to check during a verification

When the accuracy of a dispenser is verified against a master meter, the temperature factor must be neutralised, otherwise the comparison measures the weather rather than the equipment. Two practical rules apply:

  • Circulate roughly 100 to 150 litres of LPG through the system before the test so that both devices reach a similar product temperature.
  • Make sure the ATC is in the same position, on or off, on both the dispenser and the master meter. Comparing a compensated reading with an uncompensated one produces a false error figure.

The test itself is normally performed at two flow points, commonly a total of 50 litres at maximum flow and 20 litres at minimum flow, and the result is compared against the legal limits. If the deviation falls outside those limits, the adjustment is made on the calibration section of the prima meter rather than on the ATC.

Common faults seen in the field

Most ATC complaints are not caused by the device itself. The recurring causes are simpler:

  • Probe placement. A sensor that reads the temperature of the cabinet rather than the product will correct in the wrong direction.
  • Broken or missing seals. Any intervention to the probe or its wiring breaks the legal chain and requires re verification.
  • Density value left at a default. The correction depends on the density setting. If it was never adjusted for the product actually sold, the output is wrong even when the hardware is healthy.
  • Uncorrected meter drift. A dispenser that has not been checked against a master meter for a long period can be within ATC specification and still deliver the wrong volume.

What inspections look for

Inspections are the clearest reminder that ATC is part of the legal measuring system rather than a technical detail. During commissioning and later checks the recurring questions are the same: whether the probe is positioned to read product temperature, whether the connection between probe and electronic unit is sealed, whether the density setting matches the product actually sold, and whether sales are blocked while the ATC is closed.

The record keeping expected from the operator is equally simple. After every verification, the test date, the serial number of the master meter used, the measured deviation and any adjustment made should be kept in writing. That record serves as a reference for the next service visit and shows an inspector that the system is monitored. Photographing seal numbers removes most later disputes before they start.

One more detail: any software or setting intervention in the electronic unit of the dispenser can affect the ATC side as well. Verifying the system again after an electronic board replacement or a software update prevents deviations that would otherwise be noticed much later.

What this means for station operators

For a station, ATC is not an optional convenience. It protects the consumer from paying for expansion, protects the operator from delivering more product than it invoices, and forms part of the legal measuring system that inspectors examine. Treating it as part of a wider measurement discipline is what makes it effective: a correctly sealed ATC, a meter verified twice a year against a master meter, and a master meter calibrated annually by an accredited body.

2A Engineering supplies LPG dispensers, master meters and the supporting station equipment used in this chain, together with the service network that performs verification at the forecourt.

Frequently asked questions

Does ATC change the amount of LPG that is delivered?

It changes the amount that is counted, not the amount that flows. The system corrects the measured volume to a reference temperature so that the customer receives a comparable quantity of product in summer and in winter.

Can a dispenser be operated with the ATC switched off?

No. In a correctly configured system no sale should be possible while the ATC is in the closed position, and the probe and its connection must be sealed.

How often should dispenser accuracy be verified?

Checking measurement accuracy twice a year within the standard service period is the recommended practice. The master meter used for that check should itself be calibrated once a year by an accredited organisation.

Is ATC enough to keep a dispenser accurate?

No. ATC corrects temperature only. Mechanical wear in the meter is a separate source of error and can only be detected by comparing the dispenser against a reference master meter.

Who performs the verification at the station?

The work is carried out by authorised service personnel with the area around the dispenser isolated by a safety ring, since the test involves live product transfer.

Blog Archieve
Whatsapp
Trade Now!